Dyna CSADX3200 Dokumentacja Pobierz pdf (Strona 8)

BASIC OPERA TlON

(continued)

slightly. Whenever making any speed adjustments

check the unit with a voltmeter or tachometer and be

sure the speed is neither too high or low.

The engine must be run at the specified speed at

all times. Lower voltage may damage both the

generator and any load connecting to it. Running the

engine at excessively high speeds results in high

voltage, which may significantly shorten the life of

appliances being used.

3.Output voltage should be checked periodically to en-

sure continued proper operation of the generating

plant and appliances. If the generator is not equip-

ped with a voltmeter, it can be checked with a por-

table meter. Frequency can be checked by using an

electric clock with a sweep second hand. Timed

against a wrist watch or a stop watch the clock should

be correct within

2 seconds.

CONNECTING THE LOADS

Applying The Load

-Allow the engine to warm up for

two or three minutes before applying any load. This

will allow the engine to reach normal operating temp-

erature and oil to circulate throughout the engine.

A short warm-up time will permit the engine to work

more efficiently when the load is applied and will

reduce the wear in the engine, extending its life.

A. Receptacles have been provided on the control

panel for your load connections. The loads

should be applied gradually. If a large motor is

being started or multiple motors are being

started, they should be started individually and

the largest should be started first.

B. Most electric tools and appliances will have the

voltage and amperage requirements on their in-

dividual nameplates. When in doubt consult the

manufacturer or a local electrician. The nameplate

amperage rating for electric motors can be mis-

leading, see Starting Electric Motors in section B.

C.These engine generator sets are inherently self

regulating based on engine speed. The engine

governor will automatically adjust itself to the

load. No harm to the generator will result if it is

run with no load connected.

D. Proper utilization of the receptacles located on the

control panel is necessary to prevent damage to

either the receptacles or the generator. The gen-

erator is a limited source of electrical power, there-

fore pay special attention to the receptacle and

generator ratings. The nameplate rating can be ob-

tained through a combination of receptacles or a

single receptacle as long as the receptacle

amperage rating is not exceeded. Both the 120 and

240 volt receptacles can be utilized at the same

time. See section B for proper load separation.

Grounding

All units must be grounded.

A .Drive a

3/4

or 1'' copper pipe or rod into the ground

close to the engine-generator set. The pipe must

penetrate moist earth. Connect an approved

ground clamp, to the pipe. Run a no. 10 Awg wire

from clamp to the generator ground lug or the bat-

tery negative terminal. Do not connect to a water

pipe or to a ground used by a radio system.

Connecting the Battery

Enclosed with your new

generator set you will find a 12V DC connector,

lead-

wire and battery clip assembly. This lead wire set

is provided for your use in charging 12 volt batteries.

Located on the front panel is a 12 volt receptacle.

To charge your batteries plug the lead wire assembly

into this receptacle and attach the battery clips to

the battery. The red clip is positive and the black clip

is negative. If the positive and negative leads are ac-

cidentally shorted, or are incorrectly connected to

the battery, the automatic resetting DC circuit

breaker in the generator will trip to protect the gener-

ator and your battery. Once the short is removed the

circuit breaker will reset itself in about 5 seconds.

PERSONAL DANGER

Lead acid batteries produce explosive

hydrogen gas when charging. Keep

sparks, flames, and burning cigarettes

away from the battery. Ventilate the

area when charging or using the battery

in an enclosed space. Lead acid batter-

ies contain sulfuric acid, which causes

severe burns. If acid contacts eyes, skin

or clothing, flush well with water. For

contact with eyes, get immediate med-

ical attention.

LOW OIL SHUTDOWN SYSTEM

KAWASAKI Powered Generators

These engine gen-

erator sets come equipped with a standard Kawasaki

low oil shut-down system.

A.This low oil shut-down system will automatically

stop the engine well before the oil level reaches a

danger point. This feature is designed to prevent

costly repairs and downtime.

B.The low oil shut-down system consists of a float

switch and a low oil module to monitor the oil level

in the crank case. The float switch is mounted in the

engine crank case between the engine and the

generator end bracket. The module is mounted on

the engine. The module monitors the oil level via the

float switch; if the oil level is low it will short out the

engine ignition and shut the engine off. If the oil level

is low when the engine is started, the engine will

start and run for about three

(3)

seconds and shut-

down. This indicates that the oil level is low and

must be completely refilled before starting.

C. Use of this low oil shut-down system on applications

that are subject to shock, bumping or severe angles

of operation (in excess of 15 degrees) should be

avoided. This is especially true if an unexpected

shutdown would cause a safety hazard or serious

inconvenience for the operator. To disable the shut-

down system disconnect the wire running from

under the engine shroud to the control module

mounted on the engine.

1 2 3 4 5 6 7 8 9 10 11 12

Komentarze do niniejszej Instrukcji

Brak uwag

Dyna CSADX3200 Dokumentacja Strona 8

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Generatory prądu Dyna CSADX3200